SolidWorks Geeks

Solidworks 2004 add-in problem

when I start to convert into a pdf document and then emits this error

which is shown in the picture

Views: 14

Attachments:

▶ Reply to This

Replies to This Discussion

Permalink Reply by Deepak Gupta on December 1, 2009 at 11:56pm
Try re installing the blue beam software and check. And did you tried to use the PDF printer.

BTW, save your screen shot as JPEG instead of BMP. This will reduce the file size drastically as well consume less time to upload.
Permalink Reply by Tadas on December 2, 2009 at 12:18am
sorry for BMP.

I have tried to reinstall the Adobe Acrobat Reader version 9.1
but it did not help.
what is the Blue Beam?
what is a PDF printer?
Permalink Reply by Deepak Gupta on December 2, 2009 at 1:00am
Blue beam was the software that was in use for saving SolidWorks files to PDF in older versions. Can you put a screen shot of your Tools > Add In, to check what is software is in use for converting SolidWorks files to PDF.

PDF printer is like your other laser printer only. The only difference is that if is only a software which don't require any printer. You can print (convert) your SW as well windows files as PDF using these PDF printers. To name few there are PrimoPDF, PDF995. Do a search for them and install one of the then and check. I have used both PrimoPDF and PDF995 and they both work well.
Permalink Reply by Tadas on December 2, 2009 at 1:16am
thanks now i understand that is printer

and i add bad_2.jpg picture of add-in


Deepak Gupta said:
Blue beam was the software that was in use for saving SolidWorks files to PDF in older versions. Can you put a screen shot of your Tools > Add In, to check what is software is in use for converting SolidWorks files to PDF.

PDF printer is like your other laser printer only. The only difference is that if is only a software which don't require any printer. You can print (convert) your SW as well windows files as PDF using these PDF printers. To name few there are PrimoPDF, PDF995. Do a search for them and install one of the then and check. I have used both PrimoPDF and PDF995 and they both work well.
Permalink Reply by Deepak Gupta on December 2, 2009 at 1:57am
Reinstall Bluebeam.

Permalink Reply by Tadas on December 2, 2009 at 3:55am
i from other PC replaced bluebeam catalog
but problem the same

maybe you can tell me how to instal blueprint
Permalink Reply by Deepak Gupta on December 2, 2009 at 4:22am
Look for the Bluebeam installation files in SW2004 Cd's. Just run the set up again.

Did you tried installing the PDF printer??
Permalink Reply by Tadas on December 6, 2009 at 9:55pm
in cd no bluebeam instaliation were i can find so old?
:)

no pdf didn't instaled
Permalink Reply by Deepak Gupta on December 6, 2009 at 10:14pm
I have to check if I have the set up disks for SW2004. Run a search for Blue beam in all the setup cds, it should be in the 3rd or 4th CD.

OR Check here http://www.bluebeam.com/

And why didn't the PDF printer got installed.
Permalink Reply by Tadas on December 7, 2009 at 12:13am
yes and it worked

i was all doing not on administrator
:)

and user have no rights


Deepak Gupta said:
Look for the Bluebeam installation files in SW2004 Cd's. Just run the set up again.

Did you tried installing the PDF printer??
Permalink Reply by Deepak Gupta on December 7, 2009 at 1:11am
OK good. And does it mean that you are able to make the PDFs out of your SolidWorks files now.
Permalink Reply by Tadas on December 7, 2009 at 4:49am
yes i log in like administrator
ad add blueprint new
thats all
:)

thanks very much

Deepak Gupta said:
OK good. And does it mean that you are able to make the PDFs out of your SolidWorks files now.

▶ Reply to Discussion

RSS

Connect to other SolidWorks Geeks throughout the world.... Share tips, tricks and ideas...Learn to master SolidWorks.

Birthdays

Birthdays Today

Birthdays Tomorrow

© 2012   Created by Alex R. Ruiz.   Powered by

Badges  |  Report an Issue  |  Terms of Service

Sign in to chat!